Linux® is an open source operating system (OS). An operating system is the software that directly manages a system’s hardware and resources, like CPU, memory, and storage. The OS sits between applications and hardware and makes the connections between all of your software and the physical resources that do the work.

The administrative layer for system-level tasks like configuration and software install. This includes the shell, or command line, daemons, processes that run in the background, and the desktop environment.

How to Setting Up RAID 10 or 1+0 (Nested) in Linux – Linux Hint BD

Borhan Uddin

31 Mar, 2022

RAID 10 is a combine of RAID 0 and RAID 1 to form a RAID 10. To setup Raid 10, we need at least 4 number of disks. In our earlier articles, we’ve seen how to setup a RAID 0 and RAID 1 with minimum 2 number of disks.

Here we will use both RAID 0 and RAID 1 to perform a Raid 10 setup with minimum of 4 drives. Assume, that we’ve some data saved to logical volume, which is created with RAID 10. Just for an example, if we are saving a data “apple” this will be saved under all 4 disk by this following method.

Using RAID 0 it will save as “A” in first disk and “p” in the second disk, then again “p” in first disk and “l” in second disk. Then “e” in first disk, like this it will continue the Round robin process to save the data. From this we come to know that RAID 0 will write the half of the data to first disk and other half of the data to second disk.

In RAID 1 method, same data will be written to other 2 disks as follows. “A” will write to both first and second disks, “P” will write to both disk, Again other “P” will write to both the disks. Thus using RAID 1 it will write to both the disks. This will continue in round robin process.

Now you all came to know that how RAID 10 works by combining of both RAID 0 and RAID 1. If we have 4 number of 20 GB size disks, it will be 80 GB in total, but we will get only 40 GB of Storage capacity, the half of total capacity will be lost for building RAID 10.

Pros and Cons of RAID 5

Gives better performance.
We will loose two of the disk capacity in RAID 10.
Reading and writing will be very good, because it will write and read to all those 4 disk at the same time.
It can be used for Database solutions, which needs a high I/O disk writes.

Requirements

In RAID 10, we need minimum of 4 disks, the first 2 disks for RAID 0 and other 2 Disks for RAID 1. Like I said before, RAID 10 is just a Combine of RAID 0 & 1. If we need to extended the RAID group, we must increase the disk by minimum 4 disks.

My Server Setup

Operating System :      CentOS 6.5 Final
IP Address              :       192.168.0.229
Hostname                :       rd10.tecmintlocal.com
Disk 1 [20GB]           :       /dev/sdd
Disk 2 [20GB]           :       /dev/sdc
Disk 3 [20GB]           :       /dev/sdd
Disk 4 [20GB]           :       /dev/sde

There are two ways to setup RAID 10, but here I’m going to show you both methods, but I prefer you to follow the first method, which makes the work lot easier for setting up a RAID 10.

Method 1: Setting Up Raid 10

1. First, verify that all the 4 added disks are detected or not using the following command.

# ls -l /dev | grep sd

2. Once the four disks are detected, it’s time to check for the drives whether there is already any raid existed before creating a new one.

# mdadm -E /dev/sd[b-e]
# mdadm --examine /dev/sdb /dev/sdc /dev/sdd /dev/sde

Note: In the above output, you see there isn’t any super-block detected yet, that means there is no RAID defined in all 4 drives.

Step 1: Drive Partitioning for RAID

3. Now create a new partition on all 4 disks (/dev/sdb, /dev/sdc, /dev/sdd and /dev/sde) using the ‘fdisk’ tool.

# fdisk /dev/sdb # fdisk /dev/sdc # fdisk /dev/sdd # fdisk /dev/sde

Create /dev/sdb Partition

Let me show you how to partition one of the disk (/dev/sdb) using fdisk, this steps will be the same for all the other disks too.

# fdisk /dev/sdb

Please use the below steps for creating a new partition on /dev/sdb drive.

Press ‘n‘ for creating new partition.
Then choose ‘P‘ for Primary partition.
Then choose ‘1‘ to be the first partition.
Next press ‘p‘ to print the created partition.
Change the Type, If we need to know the every available types Press ‘L‘.
Here, we are selecting ‘fd‘ as my type is RAID.
Next press ‘p‘ to print the defined partition.
Then again use ‘p‘ to print the changes what we have made.
Use ‘w‘ to write the changes.
Note: Please use the above same instructions for creating partitions on other disks (sdc, sdd sdd sde).

4. After creating all 4 partitions, again you need to examine the drives for any already existing raid using the following command.
```
# mdadm -E /dev/sd[b-e]
# mdadm -E /dev/sd[b-e]1

OR

# mdadm --examine /dev/sdb /dev/sdc /dev/sdd /dev/sde
# mdadm --examine /dev/sdb1 /dev/sdc1 /dev/sdd1 /dev/sde1
```
Note: The above outputs shows that there isn’t any super-block detected on all four newly created partitions, that means we can move forward to create RAID 10 on these drives.

Step 2: Creating ‘md’ RAID Device

5. Now it’s time to create a ‘md’ (i.e. /dev/md0) device, using ‘mdadm’ raid management tool. Before, creating device, your system must have ‘mdadm’ tool installed, if not install it first.
```
# yum install mdadm             [on RedHat systems]
# apt-get install mdadm         [on Debain systems]
```
Once ‘mdadm’ tool installed, you can now create a ‘md’ raid device using the following command.
```
# mdadm --create /dev/md0 --level=10 --raid-devices=4 /dev/sd[b-e]1
```
6. Next verify the newly created raid device using the ‘cat’ command.
```
# cat /proc/mdstat
```
7. Next, examine all the 4 drives using the below command. The output of the below command will be long as it displays the information of all 4 disks.
```
# mdadm --examine /dev/sd[b-e]1
```
8. Next, check the details of Raid Array with the help of following command.
```
# mdadm --detail /dev/md0
```
Note: You see in the above results, that the status of Raid was active and re-syncing.

Step 3: Creating Filesystem

9. Create a file system using ext4 for ‘md0’ and mount it under ‘/mnt/raid10‘. Here, I’ve used ext4, but you can use any filesystem type if you want.
```
# mkfs.ext4 /dev/md0
```
10. After creating filesystem, mount the created file-system under ‘/mnt/raid10‘ and list the contents of the mount point using ‘ls -l’ command.
```
# mkdir /mnt/raid10
# mount /dev/md0 /mnt/raid10/
# ls -l /mnt/raid10/
```
Next, add some files under mount point and append some text in any one of the file and check the content.
```
# touch /mnt/raid10/raid10_files.txt
# ls -l /mnt/raid10/
# echo "raid 10 setup with 4 disks" > /mnt/raid10/raid10_files.txt
# cat /mnt/raid10/raid10_files.txt
```
11. For automounting, open the ‘/etc/fstab‘ file and append the below entry in fstab, may be mount point will differ according to your environment. Save and quit using wq!.
```
# vim /etc/fstab

/dev/md0                /mnt/raid10              ext4    defaults        0 0
```
12. Next, verify the ‘/etc/fstab‘ file for any errors before restarting the system using ‘mount -a‘ command.
```
# mount -av
```
Step 4: Save RAID Configuration

13. By default RAID don’t have a config file, so we need to save it manually after making all the above steps, to preserve these settings during system boot.
```
# mdadm --detail --scan --verbose >> /etc/mdadm.conf
```
That’s it, we have created RAID 10 using method 1, this method is the easier one. Now let’s move forward to setup RAID 10 using method 2.

Method 2: Creating RAID 10

1. In method 2, we have to define 2 sets of RAID 1 and then we need to define a RAID 0 using those created RAID 1 sets. Here, what we will do is to first create 2 mirrors (RAID1) and then striping over RAID0.

First, list the disks which are all available for creating RAID 10.
```
# ls -l /dev | grep sd
```
2. Partition the all 4 disks using ‘fdisk’ command. For partitioning, you can follow #step 3 above.
```
# fdisk /dev/sdb
# fdisk /dev/sdc
# fdisk /dev/sdd
# fdisk /dev/sde
```
3. After partitioning all 4 disks, now examine the disks for any existing raid blocks.
```
# mdadm --examine /dev/sd[b-e]
# mdadm --examine /dev/sd[b-e]1
```
Step 1: Creating RAID 1

4. First let me create 2 sets of RAID 1 using 4 disks ‘sdb1’ and ‘sdc1’ and other set using ‘sdd1’ & ‘sde1’.
```
# mdadm --create /dev/md1 --metadata=1.2 --level=1 --raid-devices=2 /dev/
```
```
sd[b-c]1
# mdadm --create /dev/md2 --metadata=1.2 --level=1 --raid-devices=2 /dev
```
```
/sd[d-e]1
# cat /proc/mdstat
```
Step 2: Creating RAID 0

5. Next, create the RAID 0 using md1 and md2 devices.
# mdadm --create /dev/md0 --level=0 --raid-devices=2 /dev/md1 /dev/md2 # cat /proc/mdstat
Step 3: Save RAID Configuration

6. We need to save the Configuration under ‘/etc/mdadm.conf‘ to load all raid devices in every reboot times.
# mdadm --detail --scan --verbose >> /etc/mdadm.conf
After this, we need to follow #step 3 Creating file system of method 1.

That’s it! we have created RAID 1+0 using method 2. We will loose two disks space here, but the performance will be excellent compared to any other raid setups.

Conclusion

Here we have created RAID 10 using two methods. RAID 10 has good performance and redundancy too. Hope this helps you to understand about RAID 10 Nested Raid level. Let us see how to grow an existing raid array and much more in my upcoming articles.

How to install WoeUSB on Ubuntu 20.04 LTS